PS 624 - Inside Angle Fitting

ps-624-no-dimensions.png
Part No. A B Finish Product Weight / Piece (lbs)
PS 624 37-1⁄2° 37-1/2° 3" (76) EG 0.58
PS 624 45° 45° 3-1/8" (79) EG 0.58
PS 624 45° 45° 3-1/8" (79) DF 0.615
PS 624 45° 45° 3-1/8" (79) HG 0.615
PS 624 45° 45° 3-1/8" (79) GR 0.58
PS 624 52-1⁄2° 52-1/2° 3-1/16" (78) EG 0.58
PS 624 60° 60° 3-1/8" (79) EG 0.58
PS 624 60° 60° 3-1/8" (79) HG 0.615
PS 624 60° 60° 3-1/8" (79) GR 0.58
PS 624 67-1⁄2° 67-1/2° 3-1/8" (79) EG 0.58
PS 624 75° 75° 3-3/16" (81) EG 0.58
PS 624 82-1⁄2° 82-1/2° 3-3/16" (81) EG 0.58

    Design Loads

    Design Loads - PS 624
    Part Number Angle  Average Ultimate Tension
    (lbs)    		  Design Tension Load
    (lbs)    		 Average Deflection at Design Tension Load
    PS 624 82-1/2° 82-1/2° 5,800 1,500 0.140"
    PS 624 75° 75° 6,000 1,500 0.147"
    PS 624 67-1/2° 67-1/2° 6,000 1,500 0.179"
    PS 624 60° 60° 5,300 1,500 0.189"
    PS 624 52-1/2° 52-1/2° 5,100 1,500 0.200"
    PS 624 45° 45° 4,300 1,400 0.190"
    PS 624 37-1/2°
    		 37-1/2° 3,300 1,100 0.158"
     
    Notes:
    1. Design loads are based on static testing with a Safety Factor = 3.5, except for **, based on ultimate strength of connection. **Safety Factor - 3.0.
    2. 1/2" Power-Strut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    3. Design loads limited to 1,500 lbs for Slip Load of Channel Nuts.
    4. Deflection measured in direction of tension load.

    General Specifications

    Standard Dimensions (Unless Shown Otherwise on Drawing):

    • Hole Diameter:  9/16"  (14mm)
    • Hole Spacing (From End):  13/16"  (21mm)
    • Hole Spacing (On-Center):  1 7/8"  (48mm)
    • Width:  1 5/8"  (41mm)
    • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

    Note:

    • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
    • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
    • Power-Strut Defender (DF):  Conforms to ASTM A1059
    • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
    • Perma-Green (GR):  Conforms to commercial standards for powder coating
    • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1
    • Plain (PL):  No finish 

    Materials & Finishes - Special Metals:

    • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
    • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
    • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.