PS 616 - 4 Hole U-Shaped Splice

Part No. Use With A Finish Product Weight / Piece (lbs)
PS 616 P1000, P1100, P2000 1-9/16" EG 2.65
PS 616 P1000, P1100, P2000 1-9/16" HG 2.809
PS 616 P1000, P1100, P2000 1-9/16" GR 2.65
PS 616 P1000, P1100, P2000 1-9/16" ZD 2.65
PS 616 P1000, P1100, P2000 1-9/16" SS 2.65

    Design Loads

    Design Loads - PS 616 (Slot Up)
    Average Ultimate Load "P"
    (lbs)
    Average Ultimate Bending Moment "A"
    (in-lbs)
     Average ultimate Bending Moment with 3 SF
    (in-lbs)
    Design Bending Moment
    (in-lbs)
    5,700 16,300  5,400 5,080

    Notes:
    1. Design Bending Moment is based on static testing with a Safety Factor = 3.2 and is limited to the PS 200 Bending Moment.
    2. 1/2" Power-Strut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    3. Design Bending Moment applies only to the PS 616 part number.

    Design Loads

    Design Loads - PS 616 (Slot Up)
    Average Ultimate Load "P"
    (lbs)
    Average Ultimate Bending Moment
    (in-lbs)
     Average Ultimate Bending Moment with 3 SF
    (in-lbs)
    Design Bending Moment
    (in-lbs)
    2,800 21,000  7,000 5,080

    Notes:
    1. Design Bending Moment is based on static testing with a Safety Factor = 4.1 and is limited to the PS 200 Bending Moment.
    2. 1/2" Power-Strut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    3. Design Bending Moment applies only to the PS 616 part number.

    Design Loads

    Design Loads - PS 616 (PS 200 2T3 Splice)
    Average Ultimate Load "P"
    (lbs)
    Average Ultimate Bending Moment
    (in-lbs)
    Design Bending Moment
    (in-lbs)
    10,200 61,200 20,400

    Notes:
    1. Design Bending Moment is based on static testing with a Safety Factor = 3.0 to the Average Ultimate Bending Moment.
    2. 1/2" Power-Strut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    3. Design Bending Moment applies only to the PS 616 part number and used in pairs, as shown.

    General Specifications

    Standard Dimensions (Unless Shown Otherwise on Drawing):

    • Hole Diameter:  9/16"  (14mm)
    • Hole Spacing (From End):  13/16"  (21mm)
    • Hole Spacing (On-Center):  1 7/8"  (48mm)
    • Width:  1 5/8"  (41mm)
    • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

    Note:

    • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
    • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
    • Power-Strut Defender (DF):  Conforms to ASTM A1059
    • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
    • Perma-Green (GR):  Conforms to commercial standards for powder coating
    • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1
    • Plain (PL):  No finish 

    Materials & Finishes - Special Metals:

    • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
    • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
    • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.