PS 3033 & PS 3033 SQ - Post Base

Part No. Finish Product Weight / Piece (lbs)
PS 3033 DF 3.954
PS 3033 HG 3.954
PS 3033 GR 3.73
PS 3033 ZD 3.37
PS 3033 SS 3.73
PS 3033 AL AL 1.35
PS 3033 EG EG 3.73
PS 3033 HG HG 3.954
PS 3033 SQ EG 3.73
PS 3033 SQ DF 3.954
PS 3033 SQ GR 3.73
PS 3033 SQ SS 3.73
PS 3033 SQ AL
PS 3033 ST ST 3.73
PS 3033 ST ST 3.73

    Design Loads (PS 3033)



    Notes:
    1. Design Loads only apply to Power-Strut brand products.
    2. Average Safety Factor = 3.7 based on static testing to the ultimate strength of connection. Design Load is limited to 3,000 lbs for the Slip Load of (2) Channel Nuts with a Safety Factor = 3.0.
    3. 1/2" Power-Strut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    4. Deflection is the average deflection reading at 3,000 lbs.  Deflection is measured in the direction of the Tension Load.
    5. Design Loads apply only to the PS 3033 part number

    Design Loads (PS 3033 SQ)



    Notes:
    1. Design Loads only apply to Power-Strut brand products.
    2. Average Safety Factor = 3.9 based on static testing to the ultimate strength of connection. Design Load is limited to 3,000 lbs for the Slip Load of (2) Channel Nuts with a Safety Factor = 3.0.
    3. 1/2" Power-Strut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
    4. Deflection is the average deflection reading at 3,000 lbs.  Deflection is measured in the direction of the Tension Load.
    5. Design Loads apply only to the PS 3033 SQ part number.

    General Specifications

    Standard Dimensions (Unless Shown Otherwise on Drawing):

    • Hole Diameter:  9/16"  (14mm)
    • Hole Spacing (From End):  13/16"  (21mm)
    • Hole Spacing (On-Center):  1 7/8"  (48mm)
    • Width:  1 5/8"  (41mm)
    • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

    Note:

    • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
    • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
    • Power-Strut Defender (DF):  Conforms to ASTM A1059
    • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
    • Perma-Green (GR):  Conforms to commercial standards for powder coating
    • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1
    • Plain (PL):  No finish 

    Materials & Finishes - Special Metals:

    • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
    • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
    • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.