PS 2651 - Beam Clamp

T1 Use With:  PS 200, PS 210, PS 300, PS 400, PS 500, PS 520
T2 Use With:  PS 100, PS 150, PS 200 2T3
T3 Use With:  PS 100 2T3, PS 150 2T3
 
Part No. Finish Product Weight / Piece (lbs)
PS 2651 T1 EG 0.83
PS 2651 T1 DF 0.88
PS 2651 T1 HG 0.88
PS 2651 T1 SS 0.83
PS 2651 T2 EG 0.92
PS 2651 T2 DF 0.975
PS 2651 T2 HG 0.975
PS 2651 T2 SS 0.92
PS 2651 T3 EG 1.12
PS 2651 T3 HG 1.17

    Design Loads

    Design Load:  1,000 lbs (4.45 kN) each

    Notes:

    1. Design loads only apply to Power-Strut brand products
    2. Use in pairs only.
    3. Safety factor = 2.5 based on ultimate strength of connection.
    4. For use with beam flanges up to 3/4" (19.1 mm) thick.
    5. PS 2651 T1 for use with PS 200, PS 210, PS 300, PS 400, PS 500, PS 520
    6. PS 2651 T2 for use with PS 100, PS 150, PS 200 2T3
    7. PS 2651 T3 for use with PS 150 2T3, PS 100 2T3

    General Specifications

    Standard Dimensions (Unless Shown Otherwise on Drawing):

    • Hole Diameter:  9/16"  (14mm)
    • Hole Spacing (From End):  13/16"  (21mm)
    • Hole Spacing (On-Center):  1 7/8"  (48mm)
    • Width:  1 5/8"  (41mm)
    • Thickness:
    • 1/4"  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220" (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

    Note:

    • When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

    Materials & Finishes

    Materials & Finishes - Standard:

    • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
    • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
    • Power-Strut Defender (DF):  Conforms to ASTM A1059
    • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
    • Perma-Green (GR):  Conforms to commercial standards for powder coating
    • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1
    • Plain (PL):  No finish 

    Materials & Finishes - Special Metals:

    • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
    • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
    • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

    * These materials have different physical properties and performance characteristics. Please contact us for design support.